Understanding Plumbing Basics is Vital for Bathtub Installation
Understanding Plumbing Basics is Vital for Bathtub Installation
Blog Article
We've noticed this great article involving Tools You Need to Install a New Bathtub listed below on the internet and believe it made sense to talk about it with you on this page.
Installing a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old tub is readily accessible, the task can move rapidly; if you need to open up a wall to eliminate the old tub as well as position the new tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will require a helper to vacate the old tub as well as embeded in the new one. See to it you have certified on your own for the job as well as fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to take into consideration employing one before you begin. Opportunities are you may require a specialist plumber to make tube links.
This article will assist you set up a brand-new tub in your shower room if you have already purchased a new tub and also do not require to alter the plan of your previous water system pipelines.
Your devices and material list should make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly troublesome due to the limited gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipes have been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous type should be connected to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Using both wooden boards under its feet, put the tub in the required position. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To set up taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water system as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the tub and also examine the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and securing around the bathtub should wait until the tub has been used at least when as this will settle it into its final setting.
Getting ready for the Installation
First of all, the sustaining framework supplied with the bath must be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop stress on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack an inflexible seal, causing the water to permeate the wall surface in between the bath and also the tiling, leading to issues with wetness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and also installations. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can break rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly readily available on the market. It is recommended to fit the tiles using water-resistant or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads on Installing A Bathtub, I thought sharing that excerpt was a good thing. Enjoyed our blog? Please share it. Let another person check it out. I enjoy reading our article about Tools You Need to Install a New Bathtub .
Check It Out Report this page